Difference between revisions of "PVC Window Frames"

From diychristmas.org wiki
Jump to navigation Jump to search
(Added a few white space lines where needed.)
 
(2 intermediate revisions by 2 users not shown)
Line 1: Line 1:
 +
Window frames are one of the easiest ways to create a clean, professional-looking display while dramatically reducing yearly installation time. This project uses lightweight PVC pipe to create durable, reusable frames that can be installed in just a few minutes each season while remaining nearly invisible during daylight hours.
 +
 +
 
[[File:2009_display.JPG|center|600px]]
 
[[File:2009_display.JPG|center|600px]]
 +
  
 
:Here's how to build long-lasting, low maintenance window frames that can be almost invisible on the house during the daytime.
 
:Here's how to build long-lasting, low maintenance window frames that can be almost invisible on the house during the daytime.
  
−
:These were constructed using 1/2" PVC pipe, T-connectors and corner connectors, then painted with flat black paint to match the color of the window shutters. The paint also helps protect the PVC from the sun's UV rays while providing a better surface for zip-tieing the lights to the frames as the flat paint provides for more friction so the zip ties don't slip. Because it wasn't possible to string lights on these frames without overlapping a bit, we tried to route the lights to minimize any overlap. In the final analysis we decided that if you didn't know there was a little overlap you wouldn't notice it!
+
:These frames were constructed using 1/2" PVC pipe, T-connectors, and corner connectors, then painted flat black to match the window shutters. The paint serves several purposes: it helps the frames blend into the shutters during daylight hours, provides additional UV protection for the PVC, and creates a slightly rougher surface that helps prevent zip ties from slipping while securing the light strings. Because the lights could not be installed without a small amount of overlap, they were routed to make the overlap as inconspicuous as possible. In practice, unless you know where to look, it is hardly noticeable.
 +
 
  
 
[[File:Hung1.JPG|300px]]  [[File:Hung2.JPG|180px]] [[File:Hung3.JPG|320px]]
 
[[File:Hung1.JPG|300px]]  [[File:Hung2.JPG|180px]] [[File:Hung3.JPG|320px]]
Line 9: Line 14:
  
 
:The frames are mounted onto the shutters with a pair of hand-formed aluminum brackets. The brackets can be easily formed in a vice using a hammer and a wooden dowel for the shape, then hand-clamped around the PVC. Slip the brackets over and behind the shutters to hang the frame.
 
:The frames are mounted onto the shutters with a pair of hand-formed aluminum brackets. The brackets can be easily formed in a vice using a hammer and a wooden dowel for the shape, then hand-clamped around the PVC. Slip the brackets over and behind the shutters to hang the frame.
 +
  
 
[[File:Bracket1.JPG|200px]] [[File:Bracket2.JPG|200px]] [[File:Bracket3.JPG|200px]] [[File:Bracket4.JPG|200px]]
 
[[File:Bracket1.JPG|200px]] [[File:Bracket2.JPG|200px]] [[File:Bracket3.JPG|200px]] [[File:Bracket4.JPG|200px]]
  
  
−
:The frames are secured from wind at the bottom with a couple zip ties through small holes drilled through frame corners. Each frame has its own 4-channel wireless controller since there are four strings of lights on each frame and the whole frame has only one A/C power wire to plug in. This makes for a very quick installation: each window takes less than 2 minutes to hang and secure.
+
:The frames are secured against wind with a pair of zip ties passed through small holes drilled in the shutter corners. Each frame uses its own four-channel wireless controller to independently control the four light strings while requiring only a single A/C power connection. This makes installation extremely quick—each window takes less than two minutes to hang and secure. Although this project originally used wireless AC controllers, the same frame design can easily be adapted for incandescent lights, LED strings, or modern smart pixel controllers.
 +
 
  
 
[[File:Fasten1.JPG|300px]] [[File:Hung4.JPG|250px]] [[File:Miniren84.jpg|200px]]
 
[[File:Fasten1.JPG|300px]] [[File:Hung4.JPG|250px]] [[File:Miniren84.jpg|200px]]
 +
  
 
:PVC makes it easy to form curved shapes using a heat gun, as we did for the arch window above the front door. Since there were no shutters on this window, we used four simple pipe clamps (painted flat black) to attach the frame to the house: two clamps support the weight at the bottom and one clamp on either side to hold it against the house.
 
:PVC makes it easy to form curved shapes using a heat gun, as we did for the arch window above the front door. Since there were no shutters on this window, we used four simple pipe clamps (painted flat black) to attach the frame to the house: two clamps support the weight at the bottom and one clamp on either side to hold it against the house.
Line 21: Line 29:
 
[[File:Arch1.JPG|300px]]  [[File:Arch2.JPG|300px]]  [[File:Arch3.JPG|200px]]
 
[[File:Arch1.JPG|300px]]  [[File:Arch2.JPG|300px]]  [[File:Arch3.JPG|200px]]
  
−
:Storage is easy -- a couple wall brackets and they hang on the wall in the garage during the off-season. At the time of this writing, these frames were 25 years old and the only maintenance has been the periodic replacement of incandescent light strings and to repair one frame that was accidentally dropped from an upper-level window during take-down one year. In 2010 the incandescent lights were replaced with quality LED strings and no maintenance whatsoever has occurred since.
+
 
 +
:Storage is simple—hang the frames on a couple of wall brackets in the garage during the off-season. At the time this article was originally written, the frames had already been in service for approximately 25 years. Aside from periodically replacing aging incandescent light strings, repairing one frame that was accidentally dropped during takedown, and upgrading to quality LED strings in 2010, the PVC frames themselves have required essentially no maintenance.
 +
 
  
 
[[File:DSCI0630.JPG|500px]]
 
[[File:DSCI0630.JPG|500px]]

Latest revision as of 15:47, 21 July 2026

Window frames are one of the easiest ways to create a clean, professional-looking display while dramatically reducing yearly installation time. This project uses lightweight PVC pipe to create durable, reusable frames that can be installed in just a few minutes each season while remaining nearly invisible during daylight hours.


2009 display.JPG


Here's how to build long-lasting, low maintenance window frames that can be almost invisible on the house during the daytime.
These frames were constructed using 1/2" PVC pipe, T-connectors, and corner connectors, then painted flat black to match the window shutters. The paint serves several purposes: it helps the frames blend into the shutters during daylight hours, provides additional UV protection for the PVC, and creates a slightly rougher surface that helps prevent zip ties from slipping while securing the light strings. Because the lights could not be installed without a small amount of overlap, they were routed to make the overlap as inconspicuous as possible. In practice, unless you know where to look, it is hardly noticeable.


Hung1.JPG Hung2.JPG Hung3.JPG


The frames are mounted onto the shutters with a pair of hand-formed aluminum brackets. The brackets can be easily formed in a vice using a hammer and a wooden dowel for the shape, then hand-clamped around the PVC. Slip the brackets over and behind the shutters to hang the frame.


Bracket1.JPG Bracket2.JPG Bracket3.JPG Bracket4.JPG


The frames are secured against wind with a pair of zip ties passed through small holes drilled in the shutter corners. Each frame uses its own four-channel wireless controller to independently control the four light strings while requiring only a single A/C power connection. This makes installation extremely quick—each window takes less than two minutes to hang and secure. Although this project originally used wireless AC controllers, the same frame design can easily be adapted for incandescent lights, LED strings, or modern smart pixel controllers.


Fasten1.JPG Hung4.JPG Miniren84.jpg


PVC makes it easy to form curved shapes using a heat gun, as we did for the arch window above the front door. Since there were no shutters on this window, we used four simple pipe clamps (painted flat black) to attach the frame to the house: two clamps support the weight at the bottom and one clamp on either side to hold it against the house.

Arch1.JPG Arch2.JPG Arch3.JPG


Storage is simple—hang the frames on a couple of wall brackets in the garage during the off-season. At the time this article was originally written, the frames had already been in service for approximately 25 years. Aside from periodically replacing aging incandescent light strings, repairing one frame that was accidentally dropped during takedown, and upgrading to quality LED strings in 2010, the PVC frames themselves have required essentially no maintenance.


DSCI0630.JPG

Retrieved from "https://www.diychristmas.org/wiki/index.php?title=PVC_Window_Frames&oldid=3545"